Products
Products
100x100 RHS BKT
The ALL SIGN SYSTEMS RHS Bracket is manufactured from Specification AISI 304 Stainless Steel and is suited for securing signs onto RHS posts up to 150x100mm. Supplied with 2x M8 LIP-LOK bolt assemblies.
$8.05
100x50 RHS BKT
The ALL SIGN SYSTEMS RHS Bracket is manufactured from Specification AISI 304 Stainless Steel and is suited for securing signs onto RHS posts up to 150x100mm. Supplied with 2x M8 LIP-LOK bolt assemblies.
$9.77
102MM ANTI ROTATION CLIP
Our Anti-Rotational Clips (ARC) are manufactured from AISI 304 Stainless Steel and provide a simple, economical and speedy solution for installing signs manufactured with ALL SIGN SYSTEMS support channel. To install a sign, insert and slide the 'foot' of the bracket into the sign's ALL SIGN SYSTEMS channel, and twist the clip through 90 degrees. The other end of the clip is then secured by the bolt. Raised pips on the inner face of these one-piece clips help prevent sign rotation. Each bracket is supplied with a M8 LIP-LOK bolt assembly.
$5.52
102MM BACK TO BACK CLIP
The ALL SIGN SYSTEMS Back to Back Clips are designed to economically facilitate the back to back mounting of signs, at the same height, avoiding the need to offset the channel extrusion. The clips are supplied with M8 LIP-LOK bolts and two clips are required per channel whether one or two post mounting. Fix sign 1 using standard Anti Rotational Clips, then offer up sign 2 using back to back clips.
$5.17
102mm bollard @ 1200mm c/w cap and plug
The ALL SIGN SYSTEMS Bollard Range are highly versatile and used in a wide range of applications. The fluted design allows for easy mounting of Signs incorporating ALL SIGN ALL SIGN SYSTEMS channel and bracket systems. Two standard sizes available or bollards can be customised to suit your specific requirements.
$103.44
102MM POST CAP (WHITE)
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$10.35
102MMx4.5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$310.50
102MMx5.5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$365.70
102MMx5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$347.30
114MM ANTI ROTATION CLIP
Our Anti-Rotational Clips (ARC) are manufactured from AISI 304 Stainless Steel and provide a simple, economical and speedy solution for installing signs manufactured with ALL SIGN SYSTEMS support channel. To install a sign, insert and slide the 'foot' of the bracket into the sign's ALL SIGN SYSTEMS channel, and twist the clip through 90 degrees. The other end of the clip is then secured by the bolt. Raised pips on the inner face of these one-piece clips help prevent sign rotation. Each bracket is supplied with a M8 LIP-LOK bolt assembly.
$5.52
114MM BACK TO BACK CLIP
The ALL SIGN SYSTEMS Back to Back Clips are designed to economically facilitate the back to back mounting of signs, at the same height, avoiding the need to offset the channel extrusion. The clips are supplied with M8 LIP-LOK bolts and two clips are required per channel whether one or two post mounting. Fix sign 1 using standard Anti Rotational Clips, then offer up sign 2 using back to back clips.
$5.17
114mm bollard @ 1200mm c/w cap and plug
The ALL SIGN SYSTEMS Bollard Range are highly versatile and used in a wide range of applications. The fluted design allows for easy mounting of Signs incorporating ALL SIGN ALL SIGN SYSTEMS channel and bracket systems. Two standard sizes available or bollards can be customised to suit your specific requirements.
$114.94
114MM POST CAP (WHITE)
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$11.50
114MMx5.5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$427.80
114MMX5.87M AL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$454.25
114MMx5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$408.25
127MMX1.5M AL POLE WHITE FOR SLIPBASE NO CAP
127mm OD Aluminium Poles (no fluted) were used for a now obsolete sign support system that does not comoly with NZTA P/24. The system requires 2 castings to be fitted (to the ground socket and pole sections) which do not comply as they are not omni directional. The system is also non compliant for Large Signs as a hinge system is not practical or economic. There is a need to carry a minimal stock of 127mm poles and castings to satisfy site relocation and damage replacement requirements. The 127mm sign supoort system has been used as a single support solution by some electronic sign manufacturers. Sourced from MCK Metals in 6m lengths MOQ 250kg
$169.85
13MM BAND-IT 201S/S BAND REG / C204B9UK
ALL SIGN SYSTEMS strapping, buckles and bucklestraps are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All bands, buckles and fittings are entirely rust and maintenance free. For the safety of operators, all bands have a full, rounded edge to minimise accidents. Standard ALL SIGNS SYSTEMS strapping is packaged in a convenient PVC dispenser (30m), which enables the sign erector to carry the band easily when climbing ladders. The dispenser is totally water resistant and will not deteriorate when used in wet conditions, thus minimising wastage.
$86.25
13MM BAND-IT Buckles Regular / C25499UK
The ALL SIGN SYSTEMS stainless steel banding system offers the sign industry the versatility of bands and fittings specially designed and packaged for use by sign manufacturers and installers. The buckles are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All buckles are entirely rust and maintenance free. Buckles are supplied in packets of 100 units. Stainless Steel banding can be used on poles 89mm OD and above.
$47.15
150x100 RHS BKT
The ALL SIGN SYSTEMS RHS Bracket is manufactured from Specification AISI 304 Stainless Steel and is suited for securing signs onto RHS posts up to 150x100mm. Supplied with 2x M8 LIP-LOK bolt assemblies.
$8.97
16MM BAND-IT 201S/S BAND REG / C205G9UK
ALL SIGN SYSTEMS strapping, buckles and bucklestraps are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All bands, buckles and fittings are entirely rust and maintenance free. For the safety of operators, all bands have a full, rounded edge to minimise accidents. Standard ALL SIGNS SYSTEMS strapping is packaged in a convenient PVC dispenser (30m), which enables the sign erector to carry the band easily when climbing ladders. The dispenser is totally water resistant and will not deteriorate when used in wet conditions, thus minimising wastage.
$106.95
16MM BAND-IT Buckles Regular / C25599UK
The ALL SIGN SYSTEMS stainless steel banding system offers the sign industry the versatility of bands and fittings specially designed and packaged for use by sign manufacturers and installers. The buckles are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All buckles are entirely rust and maintenance free. Buckles are supplied in packets of 100 units. Stainless Steel banding can be used on poles 89mm OD and above.
$57.50
19MM BAND-IT 201S/S BAND REG / C206R9UK
ALL SIGN SYSTEMS strapping, buckles and bucklestraps are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All bands, buckles and fittings are entirely rust and maintenance free. For the safety of operators, all bands have a full, rounded edge to minimise accidents. Standard ALL SIGNS SYSTEMS strapping is packaged in a convenient PVC dispenser (30m), which enables the sign erector to carry the band easily when climbing ladders. The dispenser is totally water resistant and will not deteriorate when used in wet conditions, thus minimising wastage.
$125.35
19MM BAND-IT Buckles Regular / C25699UK
The ALL SIGN SYSTEMS stainless steel banding system offers the sign industry the versatility of bands and fittings specially designed and packaged for use by sign manufacturers and installers. The buckles are manufactured from AISI 201 stainless steel which was specifically developed for banding applications. All buckles are entirely rust and maintenance free. Buckles are supplied in packets of 100 units. Stainless Steel banding can be used on poles 89mm OD and above.
$71.30
400MM GRD SKT FOR 60MM POLE
The ALL SIGN SYSTEMS Ground socket is manufactured from strong structural grade 6261 T5 or T6 alloy with Stainless Steel T304 security locking screws to retain the post. All ground sockets are powder coated to prevent corrosive attack of the aluminium by the concrete. Ground Sockets should be installed with no more than 30-60mm showing above ground level. Security locking screws should be orientated in the direction of the sign face and torqued to 18Nm2. Non-standard lengths are available to suit specific design requirements. All ground sockets supplied are fitted with a cap on the base. The cap acts as a pole stop and provides a significant advantage for installers as it prevents concrete from entering the socket when it is being positioned in the foundation. The ALL SIGN SYSTEMS Ground Socket is a purpose made product with a wall thickness of 5mm which prevents damage to the socket wall in accident situations - facilitating simple pole replacement. The ground socket for the 89,102 and 114mm diameter fluted poles have a raised internal wedge that the pole flute slides into to counter pole rotation. When used in concrete foundations, substantial enough to withstand crash impact, the ALL SIGN SYSTEMS Ground Socket has the following advantages: Economical and time saving installations avoiding the use of props to support poles while concrete foundations cure. Eliminates vandalism to poles/foundations before concrete has set. Economical replacement of damaged poles with no need to dig out and replace foundations. Simply remove the damaged pole from the ground socket and replace. Only one site visit required, no construction workers or plant and the damaged sign is replaced with minimal delay.
$32.20
400MM GRD SKT FOR 76MM POLE
The ALL SIGN SYSTEMS Ground socket is manufactured from strong structural grade 6261 T5 or T6 alloy with Stainless Steel T304 security locking screws to retain the post. All ground sockets are powder coated to prevent corrosive attack of the aluminium by the concrete. Ground Sockets should be installed with no more than 30-60mm showing above ground level. Security locking screws should be orientated in the direction of the sign face and torqued to 18Nm2. Non-standard lengths are available to suit specific design requirements. All ground sockets supplied are fitted with a cap on the base. The cap acts as a pole stop and provides a significant advantage for installers as it prevents concrete from entering the socket when it is being positioned in the foundation. The ALL SIGN SYSTEMS Ground Socket is a purpose made product with a wall thickness of 5mm which prevents damage to the socket wall in accident situations - facilitating simple pole replacement. The ground socket for the 89,102 and 114mm diameter fluted poles have a raised internal wedge that the pole flute slides into to counter pole rotation. When used in concrete foundations, substantial enough to withstand crash impact, the ALL SIGN SYSTEMS Ground Socket has the following advantages: Economical and time saving installations avoiding the use of props to support poles while concrete foundations cure. Eliminates vandalism to poles/foundations before concrete has set. Economical replacement of damaged poles with no need to dig out and replace foundations. Simply remove the damaged pole from the ground socket and replace. Only one site visit required, no construction workers or plant and the damaged sign is replaced with minimal delay.
$35.65
50x50 RHS BKT
The ALL SIGN SYSTEMS RHS Bracket is manufactured from Specification AISI 304 Stainless Steel and is suited for securing signs onto RHS posts up to 150x100mm. Supplied with 2x M8 LIP-LOK bolt assemblies.
$8.51
600MM GRD SKT FOR 60MM POLE
The ALL SIGN SYSTEMS Ground socket is manufactured from strong structural grade 6261 T5 or T6 alloy with Stainless Steel T304 security locking screws to retain the post. All ground sockets are powder coated to prevent corrosive attack of the aluminium by the concrete. Ground Sockets should be installed with no more than 30-60mm showing above ground level. Security locking screws should be orientated in the direction of the sign face and torqued to 18Nm2. Non-standard lengths are available to suit specific design requirements. All ground sockets supplied are fitted with a cap on the base. The cap acts as a pole stop and provides a significant advantage for installers as it prevents concrete from entering the socket when it is being positioned in the foundation. The ALL SIGN SYSTEMS Ground Socket is a purpose made product with a wall thickness of 5mm which prevents damage to the socket wall in accident situations - facilitating simple pole replacement. The ground socket for the 89,102 and 114mm diameter fluted poles have a raised internal wedge that the pole flute slides into to counter pole rotation. When used in concrete foundations, substantial enough to withstand crash impact, the ALL SIGN SYSTEMS Ground Socket has the following advantages: Economical and time saving installations avoiding the use of props to support poles while concrete foundations cure. Eliminates vandalism to poles/foundations before concrete has set. Economical replacement of damaged poles with no need to dig out and replace foundations. Simply remove the damaged pole from the ground socket and replace. Only one site visit required, no construction workers or plant and the damaged sign is replaced with minimal delay.
$35.65
600MM GRD SKT FOR 76MM POLE
The ALL SIGN SYSTEMS Ground socket is manufactured from strong structural grade 6261 T5 or T6 alloy with Stainless Steel T304 security locking screws to retain the post. All ground sockets are powder coated to prevent corrosive attack of the aluminium by the concrete. Ground Sockets should be installed with no more than 30-60mm showing above ground level. Security locking screws should be orientated in the direction of the sign face and torqued to 18Nm2. Non-standard lengths are available to suit specific design requirements. All ground sockets supplied are fitted with a cap on the base. The cap acts as a pole stop and provides a significant advantage for installers as it prevents concrete from entering the socket when it is being positioned in the foundation. The ALL SIGN SYSTEMS Ground Socket is a purpose made product with a wall thickness of 5mm which prevents damage to the socket wall in accident situations - facilitating simple pole replacement. The ground socket for the 89,102 and 114mm diameter fluted poles have a raised internal wedge that the pole flute slides into to counter pole rotation. When used in concrete foundations, substantial enough to withstand crash impact, the ALL SIGN SYSTEMS Ground Socket has the following advantages: Economical and time saving installations avoiding the use of props to support poles while concrete foundations cure. Eliminates vandalism to poles/foundations before concrete has set. Economical replacement of damaged poles with no need to dig out and replace foundations. Simply remove the damaged pole from the ground socket and replace. Only one site visit required, no construction workers or plant and the damaged sign is replaced with minimal delay.
$46.00
60MM ALUM BKT
The ALL SIGN SYSTEMS Bracket range includes Aluminium Uni-Clamps specifically designed to be coupled with the ALL SIGN SYSTEMS Offset Brackets for 60mm and 76mm Aluminium Fluted Poles and Steel Poles to eliminate sign rotation. The Uni-Clamp Bracket is available in a single sign configuration and Back to Back for double offset signs. Stainless steel banding is not recommended. Ensure bolts are torqued to 12Nm.
$17.25
60MM ALUM BKT BACK TO BACK
The ALL SIGN SYSTEMS AUO Back to Back Brackets work in the same way as AUO Brackets but are designed for mounting signs back to back or street name blade extrusion end to end. Ensure bolts are torqued to 12Nm.
$20.70
60MM ANTI ROTATION CLIP
Our Anti-Rotational Clips (ARC) are manufactured from AISI 304 Stainless Steel and provide a simple, economical and speedy solution for installing signs manufactured with ALL SIGN SYSTEMS support channel. To install a sign, insert and slide the 'foot' of the bracket into the sign's ALL SIGN SYSTEMS channel, and twist the clip through 90 degrees. The other end of the clip is then secured by the bolt. Raised pips on the inner face of these one-piece clips help prevent sign rotation. Each bracket is supplied with a M8 LIP-LOK bolt assembly.
$3.68
60MM BACK TO BACK CLIP
The ALL SIGN SYSTEMS Back to Back Clips are designed to economically facilitate the back to back mounting of signs, at the same height, avoiding the need to offset the channel extrusion. The clips are supplied with M8 LIP-LOK bolts and two clips are required per channel whether one or two post mounting. Fix sign 1 using standard Anti Rotational Clips, then offer up sign 2 using back to back clips.
$4.08
60MM POST CAP (WHITE)
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$2.88
60MM STEEL POST CAP HDPE WHITE
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$2.42
60MM x 3.5M STEEL POLE WHITE C/W CAP (2MM)
ALL SIGN SYSTEMS Steel Poles are supplied in either 60 or 76mm diameter and are available in a standard lengths. The Steel Poles have a white powder coated finish and are supplied with a white plastic cap. Pole thickness is 2mm.
$103.50
60MM x 4.0M STEEL POLE WHITE C/W CAP (2MM)
ALL SIGN SYSTEMS Steel Poles are supplied in either 60 or 76mm diameter and are available in a standard lengths. The Steel Poles have a white powder coated finish and are supplied with a white plastic cap. Pole thickness is 2mm.
$111.55
60MMx3.5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$110.40
60MMx4M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$115.00
75x75 RHS BKT
The ALL SIGN SYSTEMS RHS Bracket is manufactured from Specification AISI 304 Stainless Steel and is suited for securing signs onto RHS posts up to 150x100mm. Supplied with 2x M8 LIP-LOK bolt assemblies.
$8.05
76MM ALUM BKT
The ALL SIGN SYSTEMS Bracket range includes Aluminium Uni-Clamps specifically designed to be coupled with the ALL SIGN SYSTEMS Offset Brackets for 60mm and 76mm Aluminium Fluted Poles and Steel Poles to eliminate sign rotation. The Uni-Clamp Bracket is available in a single sign configuration and Back to Back for double offset signs. Stainless steel banding is not recommended. Ensure bolts are torqued to 12Nm.
$18.40
76MM ALUM BKT BACK TO BACK
The ALL SIGN SYSTEMS AUO Back to Back Brackets work in the same way as AUO Brackets but are designed for mounting signs back to back or street name blade extrusion end to end. Ensure bolts are torqued to 12Nm.
$21.85
76MM ANTI ROTATION CLIP
Our Anti-Rotational Clips (ARC) are manufactured from AISI 304 Stainless Steel and provide a simple, economical and speedy solution for installing signs manufactured with ALL SIGN SYSTEMS support channel. To install a sign, insert and slide the 'foot' of the bracket into the sign's ALL SIGN SYSTEMS channel, and twist the clip through 90 degrees. The other end of the clip is then secured by the bolt. Raised pips on the inner face of these one-piece clips help prevent sign rotation. Each bracket is supplied with a M8 LIP-LOK bolt assembly.
$4.48
76MM BACK TO BACK CLIP
The ALL SIGN SYSTEMS Back to Back Clips are designed to economically facilitate the back to back mounting of signs, at the same height, avoiding the need to offset the channel extrusion. The clips are supplied with M8 LIP-LOK bolts and two clips are required per channel whether one or two post mounting. Fix sign 1 using standard Anti Rotational Clips, then offer up sign 2 using back to back clips.
$4.08
76MM POST CAP (WHITE)
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$3.45
76MM STEEL POST CAP
White Pole Caps are supplied with all poles and are also available as separate components to suit all sizes of ALL SIGN SYSTEMS Aluminium Poles.
$3.01
76MM x 3.6M STEEL POLE WHITE C/W CAP (2MM)
ALL SIGN SYSTEMS Steel Poles are supplied in either 60 or 76mm diameter and are available in a standard lengths. The Steel Poles have a white powder coated finish and are supplied with a white plastic cap. Pole thickness is 2mm.
$135.70
76MM x 4.0M STEEL POLE WHITE C/W CAP (2MM)
ALL SIGN SYSTEMS Steel Poles are supplied in either 60 or 76mm diameter and are available in a standard lengths. The Steel Poles have a white powder coated finish and are supplied with a white plastic cap. Pole thickness is 2mm.
$151.80
76MMx3.5M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$132.25
76MMx4M AL FL POLE WHITE - C/W CAP
The ALL SIGN SYSTEMS Aluminium Fluted Poles are extruded from strong structural grade 6061 T6 aluminium and supplied with white plastic caps. They are finished with a maintenance free white polyester powder coating making them ideal for coastal locations. The ALL SIGN SYSTEMS poles are deemed to comply with the impact requirements of NZTA P24:2020 Specification for Permanent Traffic Signs. Features & Benefits Poles are light and easy to handle and convenient to transport. Pole sizes are standard allowing all available bracket types to fit. Aluminium frangible poles size for size are comparable in strength with steel equivalents. Manufactured from marine grade alloy poles will remain maintenance free. Poles are easy to install with no specialist equipment required. Frangibility is multi-directional. In the event of damage poles can be easily removed and replaced using existing foundations The alloy has the following characteristic properties: f y = 255 MPa fu = 295 MPa % elongation to failure = 7% over a gauge length of 50mm or 5.65/A Wall Thickness (mm) relating to the trough and crest of the fluting:- 60mm Pole 2.80 3.75 76mm Pole 3.05 4.00 89mm Pole 3.55 4.50 102mm Pole 4.10 5.00 114mm Pole 4.60 5.50
$147.20